Standing seam and metal panel roofing, roof repair and full replacement in Industry. We show up when we say we will, and we clean up before we go.
Metal roofing is our specialty, but shingles, gutters, soffit and leak work all get the same attention in Industry.
If two other people have caulked it and it still leaks, call us. Most stubborn leaks turn out to be flashing, a valley, or a fastener nobody thought to check.
Backed out screws, split washers, rust starting at a seam, a panel lifted at the eave. These are our roofs, and most of the time a repair is all it takes.
Full tear off, decking checked board by board, then a new metal or shingle roof over proper underlayment. You get the price and the start date before anything comes off.
A careful walk over the whole roof — panels, shingles, valleys, flashing, fasteners — plus the attic side when there is a way in. You get photos and a straight answer.
Standing seam and metal panel roofs, measured and cut on site. We help you settle on a color, set the panels straight, and trim the ridge and valleys so the whole roof sheds water the way it should.
Missing shingles get matched as close as weathering allows. Loose metal gets new fasteners and washers, and the eaves, rakes and ridge get sealed back up tight.
Reflective coatings keep a metal roof cooler in summer and seal up the small stuff before it turns into a leak.
Guards and screens so you are not up a ladder every fall digging pine needles out of the gutter by hand.
A skylight has to be woven into the roof, not caulked to it. That is the difference between a fix that lasts a season and one that holds.
Steam and hand work, never a hammer and chisel on your roof. Then we check the eaves for the damage the ice already did.
Temporary cover goes on fast, then we come back and make the permanent repair once we can see properly what we are working with.
From a few tabs to a whole slope, we fix shingle roofs without pushing you toward a replacement you are not ready for.
After a storm we walk the roof, photograph everything we find, and write an itemized estimate you can hand straight to your adjuster.
Porch roofs, additions and low slope sections that hold water instead of shedding it. We rework the flashing, seal the seams, and get water moving again.
Lifted panels, missing shingles, flashing that has given up where the chimney comes through. We find what is actually wrong, fix that, and leave the rest of your roof alone.
Hail bruises shingles and dents the softer metal on vents, valleys and gutters. We show you what we find and document it properly for the claim.
The edge of a roof is where most trouble starts. New fascia, new soffit, wrapped or painted so it stays sound.
Careful footwork, matched materials, and flashing done the way it was done when the roof went on.
The layer you never see is what keeps water out on the ugly days. We do not thin it out to save a few dollars on a bid.
Metal, shingle and low slope work on buildings where a leak costs you more than a wet ceiling. Free estimates, same as anywhere else.
Metal is what we are known for. Since 2002 the bulk of our work has been standing seam and metal panel roofs, and it is still what most Industry homeowners call us about. We measure on site, help you settle on a color, and set the panels straight.
We do shingle roofs too, and plenty of them. But if you have been thinking about a tin roof on your Industry home, that is the conversation we enjoy most — panel type, color, trim, and what it is really going to cost.
Here is what Industry homeowners tell us makes the difference.
The same family started this company putting metal roofs on neighbors houses in 2002. It has never been sold, franchised or handed off to a call center.
If your roof needs a repair and not a replacement, we say so. Plenty of our best customers are people we talked out of a job they did not need yet.
Somebody comes out, measures, gets on the roof, and leaves you a written price. No charge, no obligation, and no number that expires if you do not sign today.
Beds get covered, tear off gets hauled as we go, and a magnet goes over the drive before we pull out. Your yard should look like we were never there.
You get a start date and we hold to it. If weather moves your job we call you, rather than leaving you watching the driveway.
The questions that come up on just about every estimate we write.
A typical Industry shingle roof runs roughly $8,000 to $18,000 in 2026 for an average single family home, and more if the deck has rot or the roof is steep and cut up with dormers. We do not price off a satellite photo — somebody comes out and measures.
Yes. Gutters, guards, soffit and fascia are all part of keeping the edge of a Industry roof dry, so we handle them along with the roof instead of sending you off to find somebody else to finish the job.
Sometimes. If the decking is sound and there is only one layer of shingles, a Industry metal roof can go over the top on purlins. If there is rot underneath or two layers already on, we tear off first — and we will tell you that before you sign, not halfway through.
Plenty of them. Most Industry customers choose from around twenty standard colors, and green, burgundy, bronze, black, gray, tan and barn red are the ones people pick most. We bring the color chart out with the estimate so you can hold it up against your siding.
Much less than people expect. Over solid decking with underlayment under it, a Industry metal roof sounds about like a shingle roof from inside the house. The loud tin roof people remember was screwed straight to open purlins over a barn with nothing underneath.
A metal roof installed properly on a Industry home should give you 40 to 60 years, and standing seam often goes longer because there are no exposed fasteners. Screws and sealants on a panel roof want attention around year 20, which is a small job next to a re-roof.
Real feedback from homeowners whose roofs we have worked on.
"Roof on our shop building. They worked Saturdays so we did not have to shut the doors during the week."
"Thank you so much to the entire crew at Roofing Brothers for our amazing new tin roof! You were amazing to work with and I couldn't recommend you to others enough! Great communication, pricing, color options, efficiency, and HONESTY! If anyone needs a new roof, I highly recommend this crew! Phenomenal job."
"Old slate roof and I was afraid nobody would touch it. They matched the pieces and now you cannot tell which ones are new."
Our crews cover the surrounding area, not only the city limits.